Common Furnace Noises

Common Furnace Noises

A noisy furnace may rapidly disrupt your home’s peace and relaxation, but the good news is that furnace noises are frequently early warning signals of worse issues to come. First, our Sacramento HVAC Company describes common furnace noises to be aware of. 

What Common Furnace Noises Mean

Noisy furnace? Our Sacramento Furnace Replacement experts are here to help. First, we advise that you always use caution when troubleshooting a furnace, especially if the issue appears to be linked to the gas line in any manner. When the remedy entails more than simply changing the air filter or tightening a few screws that are easily accessible, contact our furnace repair professionals to get things back on track.

common furnace noises 

1. Banging or Popping at the Start-Up

As it starts up, you may hear a furnace popping, booming, or banging, similar to an engine misfiring.  Our Sacramento heating repair experts explain that this is unusual. For an oil or gas furnace, it might indicate that the burner is failing to attain a hot enough temperature to consume the fuel. This causes fuel to accumulate, and when the burner heats up sufficiently, the surplus gas or oil is ejected.

Do you hear any popping or banging when the unit shuts down? In such instance, you might be hearing ducts pop as they expand and compress in response to temperature fluctuations. If the situation is too bothersome to live with, search furnace services near me to enlist some help. 

2. Squealing in the Dry

When belts or bearings need to be lubricated or replaced, they make a screeching sound. Call a Sacramento furnace repair specialist to take care of this since it is more involved than you would believe. To remove filth and look for damaged or failing parts, the furnace will require cleaning and a fast tune-up.

3. Rumbling or Rattling

To troubleshoot a rattling or rumbling furnace, we must first determine the cause of the problem. Loose debris, faulty ducting, a damaged fan blade, or more significant motor difficulties are all possible causes.

4. Clicking Sounds

A clicking furnace gets grating quickly, but it’s important to be aware of the problem. Our friends over at McQuillan Bros, furnace replacement Minneapolis company, explain that clicking noises are often produced by the ignition or heat exchanger. In any case, you’ll want to have furnace repairs as soon as possible. If those components are in good operating order, you may only a furnace tune-up to prevent nuts, bolts, and other fixtures from clicking.

5. Vibrating or Whistling

Persistent whistling usually indicates that the air intake or air filter is blocked or dislodged, which causes the flowing air to generate noise. However, if you hear whistling or vibrating sounds coming from the vents, the ductwork may be loose and enabling air to escape. A thorough examination of the airflow system can reduce noise and perhaps enhance furnace performance.

Get Furnace Repair in Sacramento

Is your loud heater keeping you from relaxing or sleeping well? Our furnace repair team in Sacramento are ready to assist you with a rapid remedy. Contact Gilmore Heating, Air and Plumbing today.

Request Service

How Can We Serve You?

We are so glad you’re here! Complete the form below to get in touch, claim your coupon, or simply join our email list. 

Causes of Uneven Heating in House

Causes of Uneven Heating in House

Causes of Uneven Heating in Your Home

Despite boosting the setting of your heater multiple times to keep the cold out of your home, you may still realize that your house is not getting warm enough. A range of issues might contribute to uneven heating in the home. So, what is the cause of uneven heating in your home, and how should you address it? Our Sacramento HVAC Experts explain below.

The Most Common Causes of Uneven Heating in Your Home

Have you observed that your house has no heat in one zone and some heat in another? Here are some of the most prevalent reasons for uneven heating in houses. If you’ve been searching for heating repair near me, you’ve come to the right place! 

Causes of Uneven Heating in House

The Boiler is Undersized

Your boiler might be smaller to accommodate your home’s radiators. This is a prevalent issue in newly built homes. House builders often install the precise boiler capacity required. Since installation, you may have expanded or modified the radiators to double panels from single panels in order to provide additional heat throughout your home. Our Sacramento heating company explains that if it is unable to manage it, uneven warmth in the home may ensue.

Your Radiators Have Become Filthy

Another main reason of no heat in one zone of the house is this. Your radiators may have been sledded. So how did you know? Check to see whether the radiators are just warming up from the top. This indicates that they are working at half-power.

Your Plumbing has Become Clogged or Restricted

Our Sacramento plumbers explain that pipework can impact your heating system. Pipework can be obstructed or restricted by sled. If the sludge gets into your manifolds or valves, the water flow to the radiators will be obstructed.

Your Thermostat is Broken

This is another typical reason of inconsistency in home heating. The thermostat may be opening and shutting sooner than usual and not detecting the proper temperature.

A heat pump that isn’t working. You may discover that your Heat Pump is not opening properly. It may only partially open or may not pump at the proper typical pace.  Our friends over at McQuillan Brothers, Twin Cities Heating Company, shares that this typically indicates that heat isn’t reaching your radiators, resulting in a chilly room.

What are the best answers to what causes uneven heating in the house?

If you’re not sure what’s causing the problem, there are several options you may attempt on your own. For example, when your furnace is turned on, test your radiators to determine if the entire system is hot. Set your settings to the maximum level as well, and check to see whether the radiators are too hot to touch. Of course, you can always contact our Sacramento heating repair company for heating replacement services. 

Contact Gilmore Today 

Never disregard any problems you notice with your heater, especially during Sacramento’s cold months. The factors discussed above will assist you in troubleshooting the issue and quickly addressing it to an HVAC professional prior to inspection. Do you require the assistance of an HVAC professional for heating in Sacramento? Schedule an appointment with Gilmore today. 

sacramento heating replacement

Request Service

How Can We Serve You?

We are so glad you’re here! Complete the form below to get in touch, claim your coupon, or simply join our email list. 

Cutting Water Heater Costs

Cutting Water heater costs

Cutting Water Heater Costs

The water heater is a natural loser when it comes to energy conservation. That’s because most of us have a traditional storage-type water heater that sits there sucking up power whether we need it or not. So, how can you avoid it from being such a power guzzler? Our Sacramento water heater repair experts share their ways below. 

Ways to Cut Water Heater Costs

Heating a home is costly, but heating water is much more so. If you’ve already taken significant efforts to lower your home’s heating expenses but your utility bills remain higher than you’d like, your hot water heater might be to blame. Below are some tips and tricks to cut water heater costs. 

Cutting Water Heater Costs

#1 Lower the temperature in your tank’s thermostat.

You’ll save 3% to 5% on your bill for every 10 degrees you lower the temperature. Most water heaters are set at 140 degrees Fahrenheit, which poses a danger of scorching. Most houses should set it to 120 degrees, according to the Energy Department. That’s plenty for your requirements, as well as preventing mineral accumulation in your tank and pipes. Our Sacramento Plumbing Contractor explains how to get it to 120 degrees:

To begin, determine the current temperature of your water. Don’t put your faith in the thermostat. They are frequently incorrect. Instead, use a thermometer to check the hot water temperature at the farthest faucet from the heater. If your water heater’s thermostat doesn’t have a numbered gauge, set it halfway between “low” and “medium.” After a day, take the temperature of the tap as mentioned above. Continue adjusting until you reach your desired temperature.

Remember that some water heaters have two thermostats, one for the bottom heating element and the other for the top heating element.

#2 Reduce the amount of hot water you use

One surefire strategy to save money on hot water is to use it less.

Our Sacramento Plumbing Company explains that a family of four showering for five minutes every day wastes 700 gallons of water per week, which is enough water to last three years for one person! Also, make sure your dishwasher is set to “economy” and stop pre-washing your dishes. Dishwashers today are capable of handling a filthy dish. Scrape any leftovers into the trash or compost bin before loading.

#3 Sediment Drainage

Tanks naturally collect silt, which affects efficiency and makes energy conservation difficult. Draining the tank will maintain it in good working order. Contact Gilmore today for water heater maintenance services. We’d be happy to help you drain the sediment. 

#4 Insulate Hot-Water Pipes That Are Exposed

Water will arrive at the faucet 2 to 4 degrees warmer after you insulate your hot water pipes, which means you won’t have to wait as long for it to heat up, saving energy, water, and money.

Basement pipes that are exposed are easy targets: Pipes in crawl areas or walls that are difficult to access may not be worth the effort.

#5 Ensure that your hot water tank is properly insulated.

Wrapping an older tank with an insulating blanket is a cheap and easy method to save money, especially if it’s in an unheated location. An insulating blanket can reduce heat loss by 25% to 45 percent and save 4% to 9% on the typical water-heating cost with these older models.

Our friends at Tureks Plumbing, Appleton WI Plumber, shares that Insulating blankets are simple to use and affordable. When dressing your tank for energy efficiency, make sure you don’t block the thermostat on an electric water heater or the air inlet and exhaust on a gas water heater.

If you have a newer model that is already insulated, don’t make the mistake of assuming that adding another layer of insulation would save you money. It has the potential to obstruct vital components and become dangerous. Consult your manufacturer for more information.

Contact Gilmore Today for Sacramento Water Heater Services

Whether you need water heater repair or water heater installation, we are here for you! Contact Gilmore today for all of your Sacramento Valley plumbing needs. 

Request Service

How Can We Serve You?

We are so glad you’re here! Complete the form below to get in touch, claim your coupon, or simply join our email list. 

Problems With Older Furnaces

Problems With Older Furnaces Sacramento Furnace Replacement

Problems With Older Furnaces

How long have you had your furnace? Many homeowners find their furnace as one of those out-of-sight, out-of-mind aspects of their homes without thinking about the functionality. If you think your furnace is too old, it most likely is. Unfortunately, older furnaces can bring some problems into your home. Below, our Sacramento HVAC company shares common problems with older furnaces. 

Common Problems With Older Furnaces

To find out how old your furnace is, look at the production date on the information plate. If it’s above 15 years old, it’s in the range where a replacement is a possibility. To replace the heater with a new one, we offer furnace replacement in Sacramento. Below, our Sacramento heating company shares common problems with older furnaces. Additionally, we explain why you should consider a Sacramento furnace replacement

Problems With Older Furnaces Sacramento Furnace Replacement

Inefficient Energy

Our Sacramento furnace repair technicians explain that older furnaces typically have something to do with how old the furnace is. Furnace efficiency standards have increased, and manufacturing technology has improved as well. An older mid-efficiency furnace can have an efficiency rating of 70% to 80%, which means that 20% to 30% of the natural gas or propane is wasted. Most furnaces now have an efficiency of 85% or greater, while condensing furnaces can have efficiencies of up to 98%.

Any mechanical equipment slows down as it ages, requiring it to consume more energy to achieve the same goals. The ravages of time will lead your furnace to lose energy efficiency at the end of its life, no matter how carefully you have cared for it. Take a peek at your winter heating bill history. Have they lately started to rise? At work, that’s the old furnace, working too hard.

Degrading Indoor Air Quality

Older heating and air conditioning systems are harmful to the air that circulates in a home. They collect dirt and dust more quickly and blast it through the ducting. It’s a clue that the furnace is too old if you smell dusty scents in the house every time the furnace and blower turn on.

They Can Pollute the Environment

Old engines rattle, shriek, slam, and make a general cacophony. If your furnace is making a lot of noise and repairs aren’t helping, it’s time to think about replacing it.

Old Furnaces Can Be A Safety Hazard

When it comes to gas, oil, and propane furnaces, this is the big one. Natural gas furnaces are the most prevalent, and while they are designed to strict safety requirements, they can succumb to age. The problem is frequently found in the furnace’s heat exchanger. Corrosion is the result of many years of chemical interactions between the vapors in the combustion gas and the metal of the heat exchanger. As follows, corrosion weakens the metal, enabling fractures to appear. Our friends over at McQuillan Brothers, Twin Cities heating company, explain that a fractured heat exchanger may allow poisonous exhaust fumes into your home’s air! If we inspects your old furnace and finds rust or cracks, replacing it is the best option.

Sacramento Pre Season Tune Up

Sacramento Furnace Replacement

If you think you’re ready for a new furnace, contact our Sacramento furnace replacement company today. Our team at Gilmore would love to help you find the best make and model for your home.

Request Service

How Can We Serve You?

We are so glad you’re here! Complete the form below to get in touch, claim your coupon, or simply join our email list.