How to Inspect an AC Drain Pan



How to Inspect an AC Drain Pan

As warm air passes over the evaporator coils in your AC, water droplets form and drip into the condensate pan located beneath the evaporator coils. This condensate then flows out through the condensate drain line. However, problems can arise when the drain pan or drain line is clogged or damaged. Your AC may turn itself off, or your property may suffer water damage as condensation accumulates underneath the AC. To prevent these problems, Gilmore Heating, Air and Plumbing, the best HVAC company in Sacramento, recommends that you inspect the AC drain pan frequently, as explained below.

Step 1: Turn On the AC

It is advisable to start your inspection exercise by turning the AC on for about half an hour. This is ample time for the system to work and generate a sufficient amount of condensate to reveal any anomalies in the condensate drainage system.

Folsom AC service techs recommend that you observe the area around the indoor unit of your air conditioner. If you don’t see any moisture, chances are the drain pan, and drain line is working as they should. All the same, you need to proceed with the next steps outlined below, just to perform a thorough inspection.

Step 2: Turn the AC Power Off and Remove the Access Panel

Experts at Gilmore Heating and Air strongly recommend that you turn the power to the HVAC system off so that you reduce the risk of electrical accidents occurring while you check the drain pan.

Once you have unplugged the AC, remove the access panel so that you can see the drain pan situated inside the air handler.

Note that air conditioners usually have two drain pans. One is permanently affixed to the air handler, and it is located higher up from the auxiliary one that is easy to remove. Residential AC company in Placerville recommend that you restrict your DIY efforts to the auxiliary drain pan and let an experienced professional remove and replace the permanent drain pan since you may make a mistake that could cause bigger problems in your AC.

Step 3: Inspect the Drain Pan and Line

Residential AC maintenance personnel suggest that you use a flashlight to take a close look at the drain pan and the drain line leading away from it. See whether you can spot any visible debris or accumulations, or even damage to the drain pan.

If water is backing up in the drain pan, there could be a blockage in the drain line. Clean out any debris that you see in the drain pan and in the opening of the drain line.

Step 4: Test the Drain Mechanism

Pour a continuous stream of water into the drain pan and observe how effectively that water drains away through the drain line. If it is sluggish or backs up, Tureks Plumbing Services, a Fox Valley Plumbing company, suggests that you may have a clog or blockage in the drain line.

Step 5: Repair Minor Damage to the Drain Pan

If you notice that the drain pan is leaking, use epoxy glue to plug that small crack responsible for the leak. However, if the leak is large, Folsom AC service professionals recommend that it is a lot better to replace that damaged drain pan.

Replacing the drain pan is best left to professionals. Contact Gilmore Heating, Air, and Plumbing for expert help, especially if the permanent drain pan has a leak.

Step 6: Clean the Condensate Drain Line

Gilmore HVAC experts recommend that you clean the condensate drain line regularly in order to prevent dirt and debris from building up inside it.

Use a stiff brush to gently clean inside the drain line and remove any debris inside. You can then pour a cup of vinegar down the drain line so that any microbial growths (mold and algae, for example) can be killed before clogs develop.

In the summer, pour bleach down the condensate drain line as a way of keeping it clean. Gilmore Heating, Air and Plumbing only recommends using bleach during the summer because the constant use of the AC will generate ample quantities of condensate to wash out the bleach before it damages the drain line.

Step 7: Restore the Access Panel

Once you are satisfied with the work done in cleaning the drain line or fixing any damage to the auxiliary drain pan, restore the access panel to its position so that the air handler isn’t exposed. When everything is back in its place, residential AC maintenance personnel recommend that you power up the system and observe whether it is working well, and no condensation is accumulating beneath the air handler. If everything is as it should be, congrats!

The drain pan and drain line aren’t the only components that need regular maintenance and inspection in your HVAC system. In fact, the drain pan and drain line will have a reduced chance of developing defects if the entire HVAC system is serviced by a professional. If you haven’t had your AC system checked by a professional in a while, contact Gilmore Heating, Air, and Plumbing for a residential ac tune-up. Our experienced technicians will conduct a thorough inspection and tune-up the system so that it is back to working reliably and efficiently. Give us a call today and learn about our Sacramento AC service plans.

5 Tips for Maintaining Your AC Unit



Maintaining Your AC Unit

Maintaining your property is one of the responsibilities you have as a homeowner. Whether it’s mowing your lawn, painting your house, or having a residential ac company in Placerville, stop by for an ac tune-up. You’ll need to stay on top of home maintenance in order to keep things running smoothly. Here are some simple tips Gilmore Heating, Air, and Plumbing⁣ recommend for maintaining your ac unit. 

Change Air Filters

Can you remember the last time you replaced the filters for your central AC unit? If not, they’re probably long overdue! Folsom AC service technicians recommend that you change disposable filters every 1-3 months. The actual replacement schedule that you follow will depend on several factors, i.e., if you have pets or live in a dusty area. Replace the filters more frequently during allergy season since the filters become clogged faster during this time of the year. Replacing your home’s ac filters is quick and easy. If you need assistance, our service techs are happy to help.

Clean the Condensing Unit

Most central AC systems have an outdoor heat pump or condensing unit. This unit has a fan mounted on top of it for the purpose of dispersing heat from the condenser. Our Folsom AC service technicians recommend that you periodically hose down this unit in order to get rid of all the pollen, dirt, and grime that accumulate and clog the fins. Try to avoid using a pressure washer since this can cause irreparable damage to the condenser or fins.

Check Around the Outdoor Unit

Our friends at McQuillan Bros, an Twin Peaks HVAC company, also recommend a visual inspection around the outdoor unit. You’ll typically need at least two feet of wiggle room around the unit. While inspecting your home’s ac unit, remove any debris and trim back any bushes or other vegetation that grows too close to the unit. Residential AC tune-up professionals recommend cleaning your ac unit often if you have trees or plants that produce high counts of pollen. This will help improve the air quality in your home. 

Check the Drain Pan and Drainpipe

If you didn’t know, your air conditioning system has a drain pan and drainpipe that help to collect and channel the moisture that is extracted from the air inside your home. The drainpipe may become clogged due to the growth of mold and other biological matter, and this could block the flow of water to the outside of the home. You may face the problem of a clogged drainpipe. If so, our friends at Tureks Plumbing, a Fox Valley plumbing company, recommends that you use a wet-dry vacuum to periodically unclog the drainpipe. If you aren’t sure about your drainpipe and drain pan on your central AC unit, contact your local HVAC company for help. At Gilmore Heating, Air, and Plumbing⁣, we provide residential ac tune-up services and more!

Residential AC Tune-Up

Gilmore Heating and Air strongly recommends that Sacramento homeowners stay on top of their ac maintenance. The last thing you want to worry about is a broken air conditioning unit in the middle of summer. Our HVAC technicians will analyze thoroughly check your air conditioning system to make sure that it’s running properly. Routine maintenance is an essential part of keeping your air conditioning system up and running. Just like a car, the more you maintain it, the longer it will last. 

You don’t have to struggle to maintain your AC on your own. Gilmore Heating and Air are happy to stop by for an ac tune-up. If you need residential ac repair or replacement, give us a call today and talk to one of our experienced HVAC professionals.

Energy Efficiency and Your HVAC System



The Connection Between Energy Efficiency and Your HVAC System

When shopping around for your home’s heating, ventilation, and air conditioning system (HVAC), you’ll most likely focus on costs rather than energy efficiency. So, is price or energy efficiency more important? The short answer is both. At Gilmore Heating, Air, & Plumbing⁣, our HVAC experts share vital information about the connection between energy efficiency and your HVAC system. In this article, you’ll discover why energy efficiency matters to you.

Understanding Energy Flow

The purpose of an HVAC system is not only to warm or cool your space but to ensure comfortability and improve air quality. This is accomplished by fresh air being pulled from the outside or within the home (ventilation), which is brought into the air handling unit and drawn through filters. These filters help to remove dust, allergens, and other particles to purify the air. Then the air is sent to either be cooled or heated before cycling back out into the home. For most systems, the air moves through a network of ducts to different rooms. However, the air can also be centralized to specific rooms/areas of the house, depending on the system. 

Because there are a handful of steps before the air is purified and matched to the homeowners’ comfort, there are a number of ways to be more energy efficient with your HVAC.

Choosing the Right HVAC System

Deciding which HVAC system is right for your home can be a big decision. We asked Tureks Plumbing, a Fox Valley home-remodeling company for tips. They said that there are many factors to consider when investing in something for your home. They agree that an energy-efficient HVAC system will not only last longer but also improve home value. Plus, you’ll reduce your carbon footprint. Ultimately, an energy-efficient HVAC system is the way to go if you want to increase comfort, lower bills, and reduce energy consumption. 

Here at Gilmore Air, we will always make sure to give you plenty of options for energy-efficient HVAC products. Our Placerville HVAC experts are highly skilled in working with homeowners to find the best HVAC system for you and your family. We’re not just here for an HVAC installation – we’re here to help you through the entire HVAC replacement process from start to finish.

Committed to Quality Excellence 

At Gilmore Heating, Air, & Plumbing⁣, our team is continuously learning more about the latest Heating and Air technologies to provide you with the best HVAC service possible. Each of our certified HVAC technicians is committed to giving you a comprehensive plan to meet your HVAC comfort and energy needs. Whether you are looking to reduce high monthly energy costs, salvage your current system to sell your home, or want the most comfortable atmosphere available, we do it all.

Certified Energy Performance

Since 1979, we have been providing customers with the best service around. You can always count on us to give you honest and professional advice. We will never recommend an HVAC system that doesn’t have a long track record of exceptional performance. With the Gilmore Guarantee, you won’t have to worry about your HVAC system failing you when you need it most. If you need help selecting or replacing your HVAC system, contact Gilmore Heating, Air, & Plumbing⁣ today.

How Efficient is a 20 Year Old Furnace?



How Efficient is a 20-Year-Old Furnace?

At Gilmore Heating, Air and Plumbing⁣, we love helping our customers navigate their HVAC problems. You can always count on our Gilmore team to give you honest and professional advice. Sacramento homeowners often ask us, “How efficient is my 20-year old furnace?” In this blog, our trusted Sacramento HVAC technicians have put together the information you need to know about the efficiency of your 20-year-old furnace. 

So, How Efficient Is a 20-Year Old Furnace?

Unfortunately, at 20 years, no furnace is running as efficiently as it once was. 

For starters, HVAC repair experts confirm that any furnace that has been in use for 20 years is nearing the end of its lifespan. The components of a 20-year-old furnace suffer a lot of wear and tear over the years. The aging process plays a significant role in lowering the efficiency of the furnace.

Over the last few decades, technology has changed immensely. New technological advancements are being introduced every day, which is why cutting-edge technology two decades ago is obsolete today. Newer furnace designs and components are made to be more efficient and more durable, and these are attributes that are probably lacking in your furnace that has been in service for 20 years.

The U.S. Department of Energy indicates that a 20-year-old furnace wastes at least 22 % of the energy it consumes. In other words, you lose more than 2 dollars from every ten that you spend on heating your home.

Compare that to a new furnace whose AFUE (annual fuel utilization efficiency) rating is 95%, meaning that you only lose half a dollar for every ten dollars’ worth of energy consumed by your furnace. The rest is used to generate heat for your home. These differences add up over time, so a 20-year old furnace that isn’t as efficient as it once was is robbing you of your hard-earned money.

Signs That Your Furnace Is Inefficient

The thing with inefficiency is that it doesn’t happen overnight. Gilmore HVAC professionals say the drop in efficiency is normally a gradual process, so you are unlikely to realize it immediately when it happens. However, several signs suggest that your furnace is becoming inefficient. Here are the most telling signs according to the experienced HVAC repair technicians at Gilmore Heating and Air.

  • The gas bill is inexplicably higher than it used to be. We asked our friends at Tureks Plumbing Services, a plumbing company in Appleton, WI, if they often see this problem in home services. They said that any unusual increase in water or electricity bills is a good indication that something is not right. If you notice that your gas bill is now higher than it’s been in years, the chances are that the furnace is now working twice as hard to provide the same level of heating that it used to deliver.
  • The frequency of service calls has increased. If you are finding yourself calling a Folsom HVAC company regularly, then your components are working harder than they should and will continue to break down.
  • Hot and cold spots in sections of your home. Uneven heating can also occur in homes with new furnaces, but this is more common in households that have aging furnaces. If you have noticed hot and cold spots in different parts of your home, alongside the other signs mentioned earlier, then it is likely that your furnace is on its last life. 

Signs That Your Furnace Needs to Be Replaced

If your 20-year-old furnace exhibits the signs of inefficiency discussed above, Sacramento HVAC experts suggest that you lookout for the signs below before you start thinking about furnace replacement.

  • Old age. As already mentioned, a furnace that has been in service for two decades is on its last life. Age alone is a good indicator that your furnace will need to be replaced soon. So, speak with an HVAC company near me about your new furnace options.
  • The burner flame is now yellow. When the flame from the burner in your furnace becomes yellow, call Gilmore Heating and Air immediately. This means that your furnace is now generating carbon monoxide. This poses a grave safety risk, and HVAC replacement is the best solution to the problem.
  • No more heat. Have you noticed that you always feel cold in your home regardless of the temperature at which you set the thermostat? Sacramento HVAC repair technicians point out that your furnace may be so inefficient that it no longer generates heat. A new furnace is the best option. 

At Gilmore Heating and Air, we have extensive training and experience in helping people like you transition smoothly from their old furnaces to newer models. With the Gilmore Guarantee, you can rest assured that Gilmore Heating, Air & Plumbing⁣ is the best HVAC company for the job. Contact us today about any issues that you may be having with your furnace or any other component of the HVAC system. We will recommend the most cost-effective furnace that will address all your needs. 

Choosing the Right Sized Heat Pump for Your Home



Choosing the Right Sized Heat Pump for Your Home in Sacramento

One of the challenges that many Sacramento homeowners face is replacing their heat pump. If you live in an older home, your Sacramento HVAC repair technician will likely tell you that it’s time to replace your current heat pump with a new one. Choosing the right sized heat pump for your home can seem difficult at first. At Gilmore Heating and Air, we like to make the decision-making process as easy and as painless as possible, so we have compiled the following guide to help you get a fairly good picture of the system size that will address your needs.

Know Your Climatic Region

The first thing that you have to keep in mind when choosing the size of your heat pump is the region in which you live. This is because different regions or zones have different heating or cooling requirements. 

For example, Sacramento is in Zone 2, which isn’t as hot as the places found in Zone 1. Once you know your region (or zone in this case), you’ll have a better understanding of what size heat pump you’ll need for your Sacramento home.

Choose a System Type

The next decision that you have to make regards your preferred system type. Here, your choices are limited to either a system that can heat as well as cool your home or one that is only intended to cool the home. The HVAC professionals at Gilmore Heating and Air have seen an increasing number of homeowners opting for systems that can heat and cool the home as needed. Not sure? Discuss your heat pump replacement options with our Sacramento HVAC replacement technicians.

Determine the Size of Your Home

Folsom HVAC replacement experts explain that heat pumps come in different sizes so that the most appropriate one can be selected for a given property. If your house is 2,000 square feet, for example, then you may need a smaller sized heat pump compared to a home that is 4,000 square feet. Our friends at Tureks Plumbing, a Fox Valley plumbing company, agrees that the size of the home gives an idea about the total area for which you need a heat pump. So, the bigger the home, the larger the heat pump needed.

Determine the Heating Needed for Each Square Foot

As already mentioned, the different climatic zones have different heating requirements, and this plays a part in determining the right size heat pump for your home. For example, Sacramento lies within Zone 2, and each square foot of space in this zone requires 35-40 BTUs of heat.

To know the total amount of heat needed for your 2500 square foot home, multiply that square footage by the BTUs needed for each square foot. When you multiply 2500 by 40, you get 100,000 BTUs.

Your next task is to select a heat pump whose capacity can deliver the 100,000 BTUs. Gilmore HVAC professionals explain that heat pumps come with an energy efficiency rating. So, you will have to factor that in when selecting a unit.

For example, a unit with an output capacity of 100,000 BTUs and an energy efficiency rating of 80% will not give you the 100,000 BTUs you need to heat your home. This is because, at 80% efficiency, the unit can only give you a maximum of 80,000 BTUs.

However, if you select a unit with an output rating of 130,000 BTUs and an efficiency rating of 80%, the actual heat produced will be 104,000 BTUs, which is within the range you want.

Factors Affecting Insulation

As you may have noticed, the amount of heating needed for each square foot in any climate zone or region is given as a range, such as 35-40 BTUs for Zone 2. This range is provided to account for a number of variables, such as how well the home is insulated.

We asked Headwaters Construction Inc, a Sacramento commercial construction company, about insulation. They said that proper insulation is key to keeping the heat inside. If, for example, your home has large windows and isn’t properly insulated, the higher number will be the right one to use in your calculations. 

However, if you have a newer home with modern windows that provide a high degree of insulation, then the lower number in the range is the more appropriate one to use.

We recognize that despite our best efforts to explain how the right size of heat pump is determined, you may still be unable to select the right size heat pump for your Sacramento home. Rather than take a risk and end up with an oversized or undersized heat pump, we strongly recommend searching HVAC company near me. At Gilmore Heating and Air, our highly-trained and certified HVAC professionals can visit your home and assess your HVAC needs. Give us a call today!

8 Common Heating and Air Conditioning Problems



Common Heating and Air Conditioning Problems Sacramento Homeowners May Be Facing

Some of the common heating and air conditioning problems don’t need more than a little cleaning and adjusting here and there. Others have the potential to morph into serious problems if prompt professional attention isn’t available to resolve them quickly. Here are some of the most common heating and air conditioning problems that the experts at Gilmore Heating and Air in Sacramento have encountered over the decades.

Dirty Air Filters

One of the simplest and yet very important HVAC maintenance tasks is replacing the air filters in your home on a regular basis. When the furnace or air filter is clogged with dirt, the HVAC unit will do a lot more work to force conditioned air through that dirty filter. You would be surprised how quickly your filter can build up with debris.

That extra work done by the unit puts a strain on the system and results in a higher energy bill as well. Gilmore HVAC technicians warn that if dirty furnace filters aren’t replaced in a timely manner, the blower will be overstrained and the furnace may overheat. It is important for you to adhere to the air filter replacement schedule so you avert all the problems that can result when dirty filters stay for too long.

To get a customized filter-replacement schedule, contact Gilmore Heating and Air so that our team can assess the specific conditions in your home before recommending the best interval at which to switch out the filters. Different conditions in homes can vary from having furry pets, living in an overly dusty area, and more.

Ignition or Pilot Problems

Our friends at McQuillan Bros, an AC company in Minneapolis, explained that a defective flame sensor or burner, or even a dirty pilot can all cause the furnace ignition to malfunction. The furnace may also short cycle, lockout or perform abnormally when these problems exist. A trained Folsom HVAC service professional will be needed to check the system and identify the specific defect so that the most appropriate remedy can be implemented. Don’t delay to call Gilmore Heating and Air since the problem may escalate and necessitate HVAC replacement.

Thermostat Defects

Sacramento HVAC technicians have traced a significant number of AC problems to a malfunctioning thermostat, so it might be worthwhile for you to read the manual of your thermostat and troubleshoot any issues it may have before calling a technician for help. At Gilmore Heating and Air, we would like to keep your Folsom AC service costs minimal, so we urge you to confirm that the defect is beyond your ability to fix before you call us for help.

HVAC System Wear and Tear

The heating system has several mechanical components, any of which can malfunction. Normal wear and tear can also take a toll on the system components, such as the belts and bearings. Folsom AC service includes checking all those belts, bearings and motors to confirm that everything is as it should be.

HVAC System airflow issues, overheating or poor heating can result when the mechanical components don’t get the professional attention that they need, so make it a point to have your HVAC system tune-up completed annually by a team from Gilmore Heating and Air.
Abnormal Furnace Noises

Under normal circumstances, your furnace will emit some sounds as it is working. For this reason, the sounds that you should be concerned about are the unusual ones that develop.

For example, HVAC repair technicians in Folsom say that when a furnace starts squealing or whining, the bearings in the blower or inducer motor may be worn and are about to fail. Dirty burners and airflow problems also have the potential to trigger unusual noises.
It is prudent for you to reach out to Gilmore Heating and Air for help as soon as you hear any abnormal noises coming from your furnace. This prompt action will address the problem before it gets worse and compels you to replace your HVAC unit prematurely.

Tripped Breakers or Blown Fuses

When the furnace blower is working more than it should, it will draw more current than normal, or it may overheat. This may cause a fuse to blow or a circuit breaker to trip. Experienced HVAC replacement experts in Folsom say that the most common reason behind this is a dirty filter.
It is therefore imperative to check and replace a dirty filter before you reset a tripped breaker. If the breaker trips again, call Gilmore Heating and Air so that one of our professionals can take a look. Leaking ducts, blocked air registers and other issues may be the reason why the breaker is tripping repeatedly.

Dirty Evaporator or Condenser Coils

If your HVAC system hasn’t been serviced as regularly as it should, there is a high likelihood that its efficiency has dropped. As the dirt accumulates, the evaporator and condenser coils will be subjected to a higher rate of wear and tear.
One way to prevent this from happening is by shutting off the power to the outdoor unit and then using a garden hose to clean the coils. As for the indoor evaporator coil, you are better off calling an HVAC repair professional from Gilmore Heating and Air.

Water Leaks

High-efficiency furnaces and air conditioners produce condensate, and that is why these appliances have drain pipes to remove this water. If the drain lines are clogged or cracked, water will leak from the furnace or AC.

You can keep these drain lines clean and free from clogs by periodically running bleach through them. However, experienced HVAC replacement technicians caution that not all water leaks can be attributed to clogged or damaged drain lines. Water leaks may also result from a defect in the evaporator, the heat exchanger drain pan, or even the collector box. A Folsom AC service professional can take a look and ensure that the leak is traced to its source and is fixed before the AC and your home suffers water damage.

Many of the problems above can be prevented or addressed promptly if a professional services the HVAC system regularly. Contact Gilmore Heating and Air if you, too, would like to benefit from a team of seasoned professionals who take pride in keeping heat furnaces and air conditioners working efficiently and reliably. We will gladly partner with you to protect your investment!

Why a Clean Air Filter is Important



Importance of Clean Air Filters

Gilmore Heating, Air & Plumbing⁣ knows that changing out dirty air filters can be a hassle. Many people wait too long to install clean filters in their homes. There are many reasons to make sure that your air filters are clean and ready to perform their job. Switching out your dirty air filters could be considered a great investment in your home. Here’s why:

Clean Air Filters Protect Your Home and Health

A dirty air filter can degrade the indoor air quality of your home and increase the chance of health issues. Poor air quality can lead to the spread of disease and the aggravation of asthma symptoms.

Clean Air Filters Ensure Energy-Efficient HVAC Systems

Dirty air filters can also negatively affect the functioning of your HVAC system. Dirt in the filters can impede airflow and decrease the energy efficiency of your entire home. This can cause your energy bills to go up both in the summer and winter. This can also cause your air conditioner and heater to work harder than it would with clean air filters. This can shorten the life of a unit and cause it to have more problems.

Clean Air Filters Can Help to Prevent Issues

When you have clean air filters in your system, you can have the peace of mind that they won’t cause any issues with your HVAC units. This way, if your HVAC system does have a problem, it’s one less thing to worry about. It will save an HVAC technician time when it comes to diagnosing an issue.

Your Heating and Cooling Specialists

Gilmore Heating, Air & Plumbing⁣ has been offering exceptional heating and air conditioning repair, installation, and maintenance services since 1979. We maintain an A+ rating with the BBB and back all of our results with a satisfaction guarantee. All of our rates are kept as low as possible to ensure our services are accessible. To learn more about our heating and air conditioning services in Placerville, CA, call Gilmore Heating, Air & Plumbing⁣ today.

Is It Time to Upgrade to a New Air Conditioner?



The air conditioner is one of the most important appliances in a building. It determines how comfortable the interior setting is during the warmer months of the year. Although air conditioners are built to last for a long time, they eventually reach the end of their lifespan. Over time, issues can begin to occur, and the product may not operate well. Here are a few of the top signs that it’s time to upgrade to a new air conditioner.

1. Lack of Cool Air

One of the most obvious signs that your air conditioner is no longer operating is if cool air isn’t blowing out of the vents in the building. You may notice that the home isn’t getting cool or that certain rooms of the home are staying warm. Older AC units that need to be replaced are also prone to breaking down frequently or need repairs on a consistent basis. In some cases, it may be more cost-effective to replace the appliance rather than continuing to fix it.

2. The AC Is Old

Checking the age of your air conditioner is one of the main ways to determine if it needs to be replaced. Most air conditioners last an average of 10 years before they begin to have issues. Air conditioners undergo regular maintenance can last up to 15 years. The unit may also use Freon, which is being phased out by the government because it’s not an energy-efficient gas.

3. You’re Dealing With Expensive Repairs

Although air conditioner repairs commonly occur from time to time, it may not be worth fixing the appliance if the repairs are too expensive. In some cases, the repairs may cost more than replacing the unit, which means that it’s time to upgrade to a newer model.

Reputable HVAC Service

Contact Gilmore Heating Air & Plumbing⁣ in Placerville, CA, at your convenience to obtain reputable HVAC service. We can provide you with more information on when it’s time to replace your air conditioner. Our crew can also install a new appliance. We’re happy to offer heating and plumbing services as well.

When Should You Schedule AC Maintenance?



Knowing that air conditioners need regular maintenance is one thing; actually setting up an appointment is another. Most experts recommend that air conditioners be checked out each spring. Annual maintenance is an important factor in keeping things running efficiently. These appointments can potentially save you money in the long run by extending the lifespan of your various components.

Why You Shouldn’t Wait Until Summer

With many things, people often have a tendency to wait to address something until it’s too late. In terms of air conditioner maintenance, it’s a better idea to set up a tune-up in the early spring rather than in the summer. This allows plenty of time to examine all of your parts and make sure the whole system is functioning properly before you start depending on your AC. In the hot summer, it can be difficult to go even a day without a working air conditioner.

Removing Build-Up

During the winter, things can get blown around, and you may accumulate dust, dirt, and grime on and around your air conditioner. In the spring, we’ll be able to clean everything out so that nothing gets in the way of performance. Plus, your indoor air quality will be better.

Staying Flexible

At Gilmore Heating Air and Plumbing⁣ in Placerville, many of our maintenance appointments are routine, but occasionally we do find a bigger concern. In this case, we’ll need time to figure out what’s going on and resolve it. Our schedule is more open in early spring, and we’ll likely be able to handle things right away if you call during that time of year. Remember, the sooner you call about an issue, the more likely it is that you can catch it while it is still small.

Count on Us

Turn to Gilmore Heating Air and Plumbing⁣ if you live in the Greater Placerville region. We’ve been serving customers since 1979, and our services include those related to heating, cooling, and plumbing. Our skilled technicians are also trained in the roofing and insulation fields. We’d be happy to help in any way whether you require an installation, repair, or service. Give us a call to arrange a convenient time for us to visit you.

Signs of Problems With Your Furnace



No one wants to deal with a furnace that is not heating. Since it never happens at a convenient time, heating failures can lead to expensive emergency repair bills. If you pay attention, you may find that your furnace has been giving you signs of a necessary repair.

Strange Smells

When your heating system kicks on for the first time in the season, you may notice the slightly charred smell of a year’s worth of dust that has made its way around the burner. That smell should only last for a cycle or two. If you notice any strange odors when your system is running, it is time to bring in a professional to have a look.

Loud Noises

Every heating system makes some amount of noise as the burner ignites or blower fans turn. However, when a system begins to fail, you may hear the scraping sound of a misaligned blower fan, the high-pitched whining of a loose motor belt, or the rattle of loose screws. Pay special attention if your system starts with a bang. This may indicate that the burner ignition is not timed correctly.

Rising Heating Bills

If the cost of your heating bill is an unpleasant surprise, it may mean that your heating system is not burning fuel efficiently. If you have a gas furnace, be sure to examine the pilot light. A burner that is running properly will burn with a blue flame. A yellow pilot light not only indicates inefficient burning, but it may also indicate excess production of carbon monoxide. If you see yellow, be sure to have your system checked by a professional right away.

At Gilmore Heating, Air, & Plumbing⁣, it is our aim to keep the homes in the Placerville area at the right temperature all year long. We can read the signs of heating system problems, and we can fix them all for you. Give us a call today and let us help you with all your heating repair, maintenance, and installation needs.